Difference between revisions of "Projects:2015s1-01 LaunchBox"
(→Cubesats) |
(→Cubesats) |
||
Line 31: | Line 31: | ||
==== Cubesats ==== | ==== Cubesats ==== | ||
− | The CubeSat concept was first developed by students at California Polytechnic (Cal Poly) in 2001 as a means to reduce the cost of gaining access to space and as a cost effective method for proving new space technologies in space <ref name = " | + | The CubeSat concept was first developed by students at California Polytechnic (Cal Poly) in 2001 as a means to reduce the cost of gaining access to space and as a cost effective method for proving new space technologies in space <ref name = "Anderson 2001"> E. Anderson and J. Smith, "New technology for increased delivery potential and access into space," in Aerospace Conference, 2001, IEEE Proceedings., 2001, pp. 1/355-1/362 vol.1.</ref> <ref name="Two"> J. Puig-Suari, C. Turner, and W. Ahlgren, "Development of the standard CubeSat deployer and a CubeSat class PicoSatellite," in Aerospace Conference, 2001, IEEE Proceedings., 2001, pp. 1/347-1/353 vol.1.</ref>. |
<ref name="Test">Test reference</ref> | <ref name="Test">Test reference</ref> |
Revision as of 21:34, 13 August 2015
Cubesats are da bomb
Contents
- 1 Project Information
- 2 Aims and Objectives
- 3 Proposed Approach
- 3.1 Mission 1 Kit
- 3.2 SUSat
- 3.3 Launchbox
- 3.3.1 Proprietary EPS
- 3.3.2 Proprietary OBC
- 3.3.2.1 Needs identification and Requirements Document
- 3.3.2.2 Research
- 3.3.2.3 Trade-off Analysis
- 3.3.2.4 Generate Feasibility Report
- 3.3.2.5 Generate Map of System Using Core
- 3.3.2.6 Use Altium to design prototype of PCB for the OBC
- 3.3.2.7 Fabricate Prototype PCB of OBC and Populate
- 3.3.2.8 Prototype Testing
- 3.3.3 Autonomous ACDS
- 4 Project Management
- 5 Conclusions
- 6 References
Project Information
Background
Project Team
Morgan Smith
Aaron Williams
Jack Mclean
Mark Prodoehl
Supervisors
Commercial
Flavia Tata Nardini
Matthew Tettlow
Academic
Michael Liebelt
Matthew Trinkle
Cubesats
The CubeSat concept was first developed by students at California Polytechnic (Cal Poly) in 2001 as a means to reduce the cost of gaining access to space and as a cost effective method for proving new space technologies in space [1] [2].
Launcbox
Mission 1 Kit
Mission 1 Program
QB50
SUSat Project
ADCS sensors
Nadir Sensor
Experimental Payload: MASP
Launchbox Cubesat
EPS
Electrical power supply is the life-blood of any satellite. The design goals of an Electrical Power System for a CubeSat are to maximize available power while minimizing power consumption and weight. The EPS consists of solar panels to collect and convert solar radiation into electrical power, a battery for storage, load regulators to control power supply to subsystems and a central controller to manage these tasks. The system design must provide solutions for the interconnection of all of these systems while maximizing power production. The EPS on board the Launchbox CubeSat will be responsible for providing power to the On Board Computer, the Attitude Determination and Control, subsystem including sensors, the Telemetry Communications Subsystem (TCS), the commercial arm transponder, and up to four experimental payloads.
Solar Panels
Supply of electrical power is a fundamental requirement for successful CubeSat missions. CubeSats utilize panels comprised of several photovoltaic cells to convert solar radiation into electrical energy. Because of the size and weight constraints of CubeSats, solar photovoltaic cells are the only real viable option for power generation [8]. These solar panels are mounted on the sides of the CubeSat. The surface area of the CubeSat determines the area available for solar panels and hence determines the total amount of electrical power that can be generated [9]. There are several solar cell technologies available, the most viable of which is the triple junction type. The key advantages of the triple junction type are its high efficiency and high terminal voltage (typically 2V) [8, 10]. The high efficiency means that the limited surface area available for solar generation can be maximized compared to less efficient cell technologies. The higher terminal voltage means that less cells need to be used to form panels with usage voltage levels [10].
The configuration of a CubeSat allows only three faces of the satellite to be in sunlight at any one time and the orbital inclination (angle of orbit from the equator) of a CubeSat may often cause the CubeSat to experience extended periods of darkness (~50 minutes for a 100 min orbit at 400 km altitude [9]). These are external factors limiting production of electrical power.
A recent paper describes the total potential power supply that could be generated from CubeSats of varying sizes ranging from 1U up to 12U [11]. The Launchbox CubeSat is a 12U satellite and will most likely be of a 2U x 3U x 2U configuration. The Launchbox CubeSat would allow for the use of four 20 mm x 30 mm solar panel arrays on its sides. This means that the Launchbox CubeSat’s panels could potentially generate up to 73.6W [11]. This potential generated power is based on a CubeSat utilizing Spectrolab 28.3% efficient cells of the triple junction type. The ends of the Launchbox CubeSat will not be covered with solar panels are they are required for the communication and sensor systems.
A CubeSat’s solar panels are a key consideration in EPS development with how to best extract the limited power from the panels most efficiently of primary focus [8]. When designing an EPS, attention must also be paid to the beginning and end of life characteristics of solar cells, as solar cells will loose efficiency over their lifetime [8, 12]. This ensures the EPS can deliver enough power to the CubeSat to throughout its operational lifetime.
Maximum Power Point Tracking
As the supply of electrical power essential for the operation of a CubeSat and the amount of power generated is limited by the CubeSat surface area it is therefore imperative, that solar panels of the EPS system are flexible to allow for peak power generation at all times when the satellite is in sunlight [5, [9]. The characteristic of the power output from cells making up the panels of a CubeSat is of a non-linear nature and is affected by the level of irradiance, cell temperature and loading [13, 14].
To maximize the power produced from the solar panels of a CubeSat, a technique called Maximum Power Point Tracking (MPPT) can be used. The MPPT technique is advantageous for satellites in LEO as the Maximum Power Point (MPP) of a panel changes significantly during the orbit [11, 13]. These significant changes in the MPP during orbit are due to the large changes in solar illumination and temperature of cells when the satellite comes in and out of sunlight. MPPT causes solar panels to operate at their maximum power point MPP and thus allows the maximum possible power to be produced from them [8, 11, 14, 15]. MPPT achieves this by tracking the MPP of solar panels and utilizing a DC-DC converter [14]. Maximum power is transferred when the operated panel voltage is equal to the voltage at the MPP. The DC-DC converter provides an interface between the panels and load and by varying the duty cycle input to the DC-DC converter the panel voltage can be altered to operate at the MPP [14].
To keep the solar panel operating at its MPP, the MPP must be tracked and the voltage corrected to ensure continual operation at the MPP. This tracking can be done with either the EPS on-board microcontroller running MPPT algorithms or using specialized discrete MPPT IC’s such as the LT3652 from Linear Technologies [9] [16].
The algorithm that is primarily used by microcontrollers to track MPP is the Perturb and Observe method [13]. In this method the microcontroller measures current and voltage output by the panel, it then multiplies the current and voltage together obtaining power. The microcontroller then changes the voltage of the panel slightly by varying the duty cycle input to the DC-DC converter and recalculates the power again. Depending on whether the power has increased or decreased since the last measurement the controller can determine the change voltage required to reach the panel’s MPP [8, 11, 13, 17]. For example if the power decreased since the last measurement the controller will know the MPP is in the opposite direction.
Particular attention needs to be paid to the sampling rate of the Perturb and Observe method. In LEO the method will fail to track the MPP, becoming confused as the MPP can change rapidly, due to the varying temperatures and irradiances found in LEO [8]. MPPT can be implemented using analog circuits but is only usually used for redundancy and was not further researched [8, 18].
When MPPT techniques are not implemented solar panels have to be carefully matched to the expected load. This has problems in terms of efficiency as the panel is connected to the battery via charging circuitry; this forces the panel to operate at the batteries voltage [8, 10, 13, 14]. Hence, with this connection method power produced is dependent on the battery voltage. Operating the panel at the batteries voltage can also cause the panel to not operate at its MPP resulting in potentially power generated being wasted. A poorly designed direct battery connection can also cause battery failure due to the lack of proper charging procedures [8]. Another advantage of using MPPT techniques over direct battery connection is that MPPT gives the option of having high efficiency when using different configurations of solar panels on the same satellite, as the output voltage is not pulled to battery voltage [10].
Load Regulators
Load regulators allow the EPS to provide different voltages from a single power source (the battery). Experience from previous missions and publications suggest that the use of synchronous buck (voltage step down) and synchronous boost (voltage step up) converters provide a flexible and efficient means of power regulation [11, 19] (Clyde space EPS).
An alternative solution is to use a single-ended primary-inductor converter (SEPIC) [7, 20]. A SEPIC converter allows for both step-up and step-down voltage conversion [15]. Both options have been used in commercial-off-the-shelf EPS boards with the former offered by Clyde space [18] and the latter offered by pumpkin [21].
Batteries
The solar panels of a CubeSat cannot generate electrical power during the dark portion of the orbit; therefore an energy storage device is needed to allow the CubeSat to continue to operate. CubeSats utilize batteries to fulfill this energy storage need allowing them to operate throughout the entire orbit. Utilizing batteries also allows the EPS to handle the peak power demands of a CubeSat when the input of energy from solar panels may not be sufficient to power all systems [8, 12, 22, 23]. The sizing of a CubeSats battery is dependent on the mission and is calculated using a power budget; the power budget calculates the average and peak powers consumed by the CubeSat [8].
Batteries are the most sensitive component of an EPS, they are quite susceptible to the temperature and vacuum effects of LEO, failing if not properly managed. Battery heaters are therefore often implemented in EPS designs to ensure the battery is operated within temperature limits[12, 24].
The battery chemistries most often implemented in CubeSat applications are the lithium ion and lithium polymer types. This is due to their ability to be recharged, reliability, compact size, low weight, high power density and low self-discharge [8, 9, 15, 23]. The low weight is an important factor as batteries account for a large portion weight in a CubeSat [11, 15]. Using lithium polymer batteries is quite new in CubeSat applications. They offer several advantages of the lithium ion type. They have better energy densities, are less flammable and have more compact form factors allowing for easier placement. However as they still new, data on their space suitability is often unavailable having to be tested before integration into a CubeSat [18, 24].
Microcontroller
To manage the operations of an EPS and ensure that all subsystems interface with one another, a microcontroller is used. The primary requirement placed on the microcontroller is the ability to perform Digital Signal Processing (DSP) in order perform the calculations required for monitoring charge and health of batteries using equivalent circuit battery models [11]. Several microcontrollers have been used in the literature ranging from the Texas Instruments TMS320F28335 [11, 25] to the Reneses RL78/G13 [9].
The microcontroller is also tasked with monitoring the health of the EPS system via communication with embedded sensors on the EPS board, the solar panels, and battery. Such parameters monitored are generally temperature, voltage, and current. The microcontroller communicates with the satellite’s OBC making measured EPS parameters available and allowing the OBC to turn on and off systems supplied by the EPS [7, 9, 11, 15, 25].
Protection Circuitry
Increased radiation levels at CubeSat orbital altitudes produce undesirable effects on any data stored memory circuits [26]. This radiation causes an increased probability of upsets within the memory where bits flip, changing overall values. This problem can cause latch ups and failure of computer system operations thereby creating situations where subsystems may draw excessive amounts of current [13]. It is therefore a key requirement of an EPS to provide protection to itself, the supplied subsystems and batteries from these events. If batteries are overcharged or discharged they can become damaged loosing valuable capacity or even fail completely. Therefore the EPS must protect batteries not only from over discharge but also over charge. The need for a battery protection is a requirement derived from the Cal Poly CubeSat specifications [27].
The EPS can provide protection using several methods. These methods are the use of current limiting circuitry, disconnecting of loads and fuses [12, 13]. It should be noted that some batteries may come with protection circuitry built in allowing battery protection circuitry to be omitted form the EPS board [12, 24].
OBC
Microcontroller
Interfacing
Memory: Primary
Memory: Secondary
ADCS
Sensors
Actuators
Autonomous System
Experminetal Payload: Mission 1 Experiments
Aims and Objectives
Mission 1 Kit
SUSat
ADCS sensors
Nadir Sensor
Sun Sensor
Experimental Payload: MASP
Launchbox
Proprietary EPS
Proprietary OBC
Autonomous ADCS
Proposed Approach
Mission 1 Kit
Hardware Prototype Development
Software Prototype
Testing
Hardware Integration
Testing
SUSat
ADCS Sensors
Nadir Sensor
Sun Sensor
Hardware Functionality Test
Software Implementation of Sun Sensor Algorithm
MASP Payload
Inquiry into Tracking Limitations and Techniques
Implementation and Testing of the Tracking Algorithm
Launchbox
Proprietary EPS
Proprietary OBC
Needs identification and Requirements Document
Research
Trade-off Analysis
Generate Feasibility Report
Generate Map of System Using Core
Use Altium to design prototype of PCB for the OBC
Fabricate Prototype PCB of OBC and Populate
Prototype Testing
Autonomous ACDS
Project Management
Budget
Risk Analysis
WBS
Gantt Chart
Conclusions
References
- ↑ E. Anderson and J. Smith, "New technology for increased delivery potential and access into space," in Aerospace Conference, 2001, IEEE Proceedings., 2001, pp. 1/355-1/362 vol.1.
- ↑ J. Puig-Suari, C. Turner, and W. Ahlgren, "Development of the standard CubeSat deployer and a CubeSat class PicoSatellite," in Aerospace Conference, 2001, IEEE Proceedings., 2001, pp. 1/347-1/353 vol.1.
- ↑ Test reference