Projects Lab

Introduction

This page gives an overview of the various project areas and their current allocations.

Facility	Location	Purpose	Status	Access
SET Software Project Lab	N204, Engineering North	For dedicated systems allocated to project to run specific software, or where system is being customized and modified, or for using large datasets or require secure physical access to data and results.	Available	Honours/Masters students/groups can apply for a dedicated computer for their project using form.
Ad-hoc CATS computers for Honours/Masters students	S326, Engineering South	Ad-hoc access to systems with engineering software that will not be booked for classes and so be available for students for ad-hoc access during teaching times.	Available	Honours/Masters students should be able to access using swipe card.
SET Computer Simulations Lab	ASPER 103, Santos	Dedicated powerful system temporarily required to run medium to large simulations where other options such as HPC are unsuitable.	Available	Honours/Masters students/groups can apply for access to room using form.
SET Electronic Projects Lab	EM307, Engineering Maths	Dedicated systems allocated to project where there is a requirement to integrate with hardware. Hot desk option also available.	Available	Honours/Masters students/groups can apply for a dedicated computer/bench/equipment for their project using form.

The SET Projects Lab (EM307) contains 24 benches, each with a digital storage oscilloscope, arbitrary function generator, tri-channel power supply, multimeter and PC. Hot desks with specialist RF equipment and mixed-signal oscilloscopes (featuring logic analysers) are also nearby in the area, as well as a small drone/rover testing area (EM306) and PCB prototyping workshop (EM315).

The Power Lab benches setup is identical to that in EM307 in most cases, but with close access to test gear suited to electrical projects (e.g. mains power analysers) and qualified personnel (e.g. electricians). 11th July 2022: area currently under refurbishment. Contact Phil in workshop opposite for further details.

Further information regarding these areas would have been presented during the Projects Introductory Session, for which documentation should be available for through MyUni.

Project bench allocations

Below is info on access times and the current state of bookings. A hyphen (-) indicates not allocated. All areas (excluding those with general 24/7 access) are not available outside standard business hours unless noted.

An induction needs to be completed in order to gain access to the areas below and be allocated a bench.

Access times

Area:	Access times (after induction):
SET Electronic Projects Lab (EM307)	Weekdays 7:00am-10:30pm and weekends/public holidays 9:00am-5:30pm (via EM lift).
SET Software Projects Lab (N204)	24/7 all days.

SET Electronic Projects Lab (EM307)

Bench EM307-xx:	Group allocated:	Comments:
01	63241, Vision Based Autonomous Circuit Racing using Machine Learning
02	73241, Vision Based Autonomous Circuit Racing using Machine Learning
03	73266, Benchtop 3 Phase Generator Unit
04
05
06
07
08
09
10	M. Parker/B.W. Ng, Multistatic Passive Radar	Summer research until 27/02/2023.
11
12
13
14
15
16	A. Allison, continuing work on project 13110, Arduino-based CSMA/CD	Lab equipment loaned out to SAS.
17	W.K. (Billy) Ng/N. Ertugrul, research	Tentative until before 2023s1.
18
19
20
21	M. Rahimi (intern)/B. Ng	Until 27/02/2023.
22
23
24	63300, A Microcontroller-based Battery Logging System

Bench layout:

(North)

01	02	03	04		05	06	07	08	09		10
11	12	13	14		15	16	17	18	19		20

21

22

23

24

SET Software Project Lab (N204)

Bench N204-xx:	Group allocated:	Comments:
01	Tianchang Ma	Research until 27/02/2023.
02	T. Murray/N. Nguyen Trong	Summer research until 27/02/2023.
03
04
05		Reserved for HGC/KM. DST PC.
06
07
08
09
10
11

Bench layout:

(West)

06	05	04	03	02	01
11	10	09	08	07

Self-service areas

Students will also gain access to the facilities below after completing an induction and being allocated a project bench by a technical staff member.

Area:	Location:	Access times/comments:
EEE Projects Lab Workshop	EM315	Accessible weekdays 10am-4pm. Contains specialist PCB prototyping equipment (listed in next section).
Electrical projects labs electronics prototyping area	NG08	Accessible weekdays 10am-4pm. As above (including a PCB mill), but with a simpler soldering setup, mainly for use by EEE students working around the area and mecheng/other groups.
SET Computer Simulations Lab	ASPER 1.03	Accessible 24/7. Contains about 22 PCs for use by Honours/Masters project students.
Final Year Project Room	S326	Accessible 24/7. Contains about 16 CATS imaged PCs for use by Honours/Masters project students

Again, please refer to your Projects Introductory Session resources for more information.

Accessing specialist equipment/hot desks

Hot desks containing the specialist equipment below are bookable though: https://www.eleceng.adelaide.edu.au/projlab. Bookings are made in three hour slots, of which two are available per day. Please contact a staff member on the first instance of needing to use the equipment for a brief intro and induction (if required).

Item:	Location:	Induction required:	Link:
LPKF ProtoMat S63 PCB milling machine	NG08/EM315	Yes.	https://www.lpkfusa.com/datasheets/prototyping/s63.pdf
LPKF ProtoFlow S PCB reflow oven	NG08(?)/EM315	Yes.	http://www.lpkfusa.com/SMTAssembly/protoflow.htm
FlashForge Creator Pro 3D printer	EM315	Yes.	https://www.flashforge.com/product-detail/4
Keysight FieldFox network analyser	EM307	Intro session.	https://www.keysight.com/au/en/product/N9923A/fieldfox-a-handheld-rf-vector-network-analyzer-4-ghz-6-ghz.html
Tektronix MSO2014B mixed signal oscilloscope (with DPO2EMBD embedded serial triggering and analyser module)	EM307	Intro session.	http://www.tek.com/oscilloscope/mso2000-dpo2000

(info about other RF and soldering equipment to be added)